 | How to Measure for New Cabinet Doors |  |
 | The FIRST Most Important Thing about measuring for your doors is this: You must order the EXAC |
|
|
| Refacing Instructions | |
| Tools Needed• tape measure• 150 grit sandpaper or sanding block • razor knife • scissors • tack cloth • hammer • self-adhesive applicator • 4” straight-edge or putty knife • adhesive spray or varnish • |
|
|
| How to Add Hinge Boring for Concealed Hinges |  |
| HINGE BORING FOR FULLY CONCEALED HINGESSINCE HINGE BORING IS A "SECONDARY" OPTION, YOU WON'T BE ABLE TO ADD HINGE BORING UNTIL AFTER YOU'VE ENTERED YOU |
|
|
| How to Install Veneer Video | |
| View our video on installing Veneer:http://www.reface.com/video.htmlNOTE: You must be using Microsoft Internet Explorer browser to view this WMV file. It |
|
|
| Hinge Boring | |
| If the CLOSED, HANGING door has the HINGES on the LEFT, the door is BORED "LEFT". "Bored" Left and "Hinged" Left mean the same thing.. HINGE SIDE DOESN'T MATTER ON SYMMETRIC |
|
|
| What Glass Size should I get to fit a Mullion or Frame Only Door? | |
| When ordering a "Frame-Only" or "Mullion" Door, you will be required to supply your own Glass. |
|
|
| What if my Door choice doesn't have any Matching Drawer Fronts ? | |
| Here's an Example:There is no specific MATCHING Drawer Front that is made to match to the 501 door, ( would have been called a "501F" ).If you can make it bigger than the MINIMUM size for th |
|
|
| Hinge Boring: Center Of Bore | |
| The Center Of Bore is the location of the Middle-point (center) of the holes in relataion to the Top and Bottom of the Door.You can customize these locations by specifying a value from 2" - 6". |
|
|
| Where can I find Decorative BASE MOULDING ? | |
| The Factory does not offer matching Base Mouldings at this time. The stain itself is NOT available separately, because it is a Pro-type , sprayed-on "toner", not a wipe on stain, and cannot be shipped because it is flammable.You can o |
|
|
| How to Reface your Cabinets (Quality Doors recommended refacing instructions) | |
| Tools you will need: • tape measure• 150 grit sandpaper or sanding block • razor knife • sciss |
|
|
| HOW TO INSTALL GLASS IN A FRAME-ONLY OR MULLION DOOR | |
| NEARLY ALL PROFESSIONALS PUT A BEAD OF CLEAR SILICONE ON THE INSIDE 90 DEGREE "CROTCH" WHERE THE GLASS WILL SIT, AND LAY THE GLASS IN, ALLOWING THE SILICONE TO STICK TO IT AS WELL AS 'SANDWICH' AROUND THE EDGES. DON'T USE TOO MUC |
|
|
| Should I Sand All the Cabinet Seams Smooth on the Front Frames Before Installing the Veneer ? | |
| We do!When the Vertical Sides of two cabinets Do NOT line up perfectly, most people simply use Two pieces of veneer to cover the combined stile, or put one piece of veneer over both stiles and simply let the 'lump' show.Small |
|
|
| How to measure for drawer boxes | |
| How to Measure for Drawer Boxes when using the drawer slide kits that we sell. |
|
|
| HOW TO AVOID ORDERING LARGE PANELS AND PAYING OVERSIZE FREIGHT CHARGES | |
| Shipping is generally FREE* on orders over $250.00....There is a $12.50 charge for orders less than $250.00. |
|
|
| How to Order Mullion Doors or Frame Only doors | |
| You MUST order the FRAME-ONLY doors separately from the standard doors. Since they use a completely different pricing scheme, We needed to make a separate category for them.This example is for the 700 series RTF doors, but the 200 / 300 series a |
|
|
| Veneer Installation tips from the professionals - install it like a pro ! | |
| When the Vertical Stiles of Two cabinets Do NOT line up perfectly, most people simply use Two pieces of veneer to cover the combined stile, or put one piece of veneer over both stiles and simply let the 'lump' show.S |
|
|
